Looking to update your fuel cap? This is a cost effective, sporty, aluminum alternative to the factory cap. It resembles the tequipment cap available on the water-cooled models. It is a quality tuning product manufactured by dansk. They offer a complete line of tuning and performance parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment manufacturers (oem) to Porsche in Germany. Oem non-locking, screw type fuel cap sourced in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary ...(choose a part on the right to read more)

General Fitment

Does your car pull to one side when you hit the brakes or let go of the wheel? Do you notice one wheel seems to “get hot”? Are your calipers leaking or stuck even though you have cracked the bleeder nipples? You may need to rebuild your calipers. These kits include seals, piston clips, and boots; and with a little labor and paint, will look new as well. Reasonably priced, they sure beat the price of a new caliper!

View/Change Diagram

928 1987-91 - Brakes/Wheels	928 1992-95 - Brakes/Wheels
928 1992-95 - Brakes/Wheels	944 1989-91 - Brakes/Wheels
944 1989-91 - Brakes/Wheels	911 1989-94 - Brakes/Wheels
911 1989-94 - Brakes/Wheels	911 1989-94 - Brakes/Wheels
968 1992-95 - Brakes/Wheels	968 1992-95 - Brakes/Wheels
911 1994-98 - Brakes/Wheels	911 1994-98 - Brakes/Wheels

The 11.8:1 compression will provide you with more acceleration than kits with 11.3:1 compression. For track use we recommend more aggressive cam (maximum valve lift (tdc) of 2.1 mm) . Piston's has very deep pockets for use with sport valves. These are 107 mm in size so are slip fit and do not require modifications. This kit is ideal for track use but can also be used on the street, it will add 35+ hp (depending on your additional modifications). Mahle pistons are forged for substantially higher and more uniform strength over pistons that are cast. Mahle cylinders are manufactured from st52 steel which has extremely high thermal resistance, they are nikasil coated which reduces wear and friction. We also have t...(choose a part on the right to read more)

This is a genuine door seal that seals the entire door and window frame. As these classics age the original gasket can become brittle and will crack, so it is essential that it is in good order as it keeps moisture out of the cabin. Sold individually. 1 necessary per car.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

We suggest periodically checking your gas cap seal for fine cracks which produce fumes. If you replace the cap and the fumes persist, check the fuel filler neck, fuel lines, expansion tank and vent shut off valves. Oem (original equipment manufacturer) bayonet locking type fuel cap sourced in Germany to ensure quality, reliability and precise fitment. Sold individually. 1 necessary per car. Please note: please check the model fitment tab to ensure accurate fitment.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

3m window weld primer is important to both seal the track around the windshield frame to cover scuff through scratches as well as provide a good sealing sticking surface for the butyl tape before you stick the windshield.

We suggest periodically checking your gas cap seal for fine cracks which produce fumes. If you replace the cap and the fumes persist, check the fuel filler neck, fuel lines, expansion tank and vent shut off valves. Quality replacement part manufactured by dansk. They offer a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment manufacturers (oem) to Porsche in Germany. Sold individually. 1 necessary per car. Please note: please check the model fitment tab to ensure accurate fitment.

...(choose a part on the right to read more)

This steering rack is a remanufactured part with a core, as such an additional charge (a core deposit) will be added to the purchase price of the part. After receiving your new part, kindly send back your old part, or core . Once the core is returned to us and it has been inspected to ensure it is rebuild-able and resell-able, the core deposit will be refunded. The remanufacturing process includes full inspection and testing for structural integrity. We then disassemble and bead blast to remove corrosion. Internals are micro-finished to OEM specifications. Sealing surfaces are carefully checked and restored prior to installing new premium seals and o-rings. Each unit is then carefully tested for full functional...(choose a part on the right to read more)

Send us your OEM transmission mount bracket and we will restore it to better than new condition! Our service includes removal of the old mount, media blasting, proper installation of the new mount and protective seal coating. Our mount is remanufactured in europe by an OEM supplier using the finest materials. It is a 65 shore rubber hardness value which is the same as the what was standard on these cars. Simply order and send us your OEM bracket, we will take care of the rest. Approximate lead time is estimated between 3-6 weeks.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

Send us your OEM transmission mount bracket and we will restore it to better than new condition! Our service includes removal of the old mount, media blasting, proper installation of the new mount and protective seal coating. Our transmission mount is manufactured in europe by an OEM supplier using the finest materials (high carbon steel, 7075 t6 aluminum and 85 shore rubber - rs spec). Simply order and send us your OEM bracket, we will take care of the rest. Approximate lead time is estimated between 3-6 weeks.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

This is a genuine door seal that seals the entire door and window frame. As these classics age the original gasket can become brittle and will crack, so it is essential that it is in good order as it keeps moisture out of the cabin. Sold individually. 1 necessary per car.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

We suggest periodically checking your gas cap seal for fine cracks which produce fumes. If you replace the cap and the fumes persist, check the fuel filler neck, fuel lines, expansion tank and vent shut off valves. Quality replacement part manufactured by dansk. They offer a complete line of replacement parts to complement the entire Porsche model range. All dansk products are manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. This commitment has made dansk one of the original equipment manufacturers (oem) to Porsche in Germany. Sold individually. 1 necessary per car. Please note: please check the model fitment tab to ensure accurate fitment.

...(choose a part on the right to read more)

Replace worn-out original soft rubber (65 shore hardness value) control arm bushings with our FVD clubsport series. They are made from rubber with a 85 shore hardness value which is the same as the rennsport models. 85 shore is more durable, provides more positive suspension location and is quiet and more forgiving than a monoball upgrade. This is the ideal upgrade for street and light track / clubsport use. This bushing set is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes 85 shore hardness value cores. This is a front and rear bushing for the front lower control arm (wishbone). 2 sets are necessary per car.

This item may need to be sourced from germ...(choose a part on the right to read more)

Replace worn-out original soft rubber (65 shore hardness value) track rod bushings with our FVD clubsport series. They are made of rubber that has an 85-shore hardness value, the same as the rs models. 85-shore is more durable, provides more positive suspension location and is quiet and more forgiving than a monoball upgrade. This bushing is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes an 85-shore hardness value core. Sold individually. 8 are necessary per car. Please note: this does not include the track rod, the picture circled in red is just for reference.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once orde...(choose a part on the right to read more)

Replace worn-out original soft rubber track rod bushings with these OEM replacements. They are made of rubber that has a 65-shore hardness value, just like the oem. They will restore the original ride comfort and are more forgiving than the clubsport (85 shore rubber). This bushing is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes a 65-shore hardness value core. Sold individually. 8 are necessary per car. Please note: this does not include the track rod, the picture circled in red is just for reference.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or re...(choose a part on the right to read more)

- + 20 crank hp & + 14 crank torque. - 200 cell hjs tri-metallic "hd" cats. - 2 tubing (50 mm) with motorsport merge collector. - weighs 18.5 lbs. (8.4 kg). - 1.5 lb (9.1 kg) saving's over OEM header. - German v2a - x5crni18-10 - 1.4301 stainless steel for improved durability. - works with OEM sealing rings and clamps. See below for part numbers. - made in Germany. - reduces thermal load and backpressure to for more torque in the mid-range and hp on the top end. Be sure to add new clamps and sealing rings to your order. 2 qty. Clamps are needed, they are part # 99711133690 and 2 qty. Sealing rings are needed, they are part # 98011156100. Our latest development for the GT3 is aimed at those who are looking fo...(choose a part on the right to read more)

The brembo gran turismo s (gt-s) braking system is ideal for clubsport and sprint type track events. The GT-s type iii system utilizes brembo type iii aggressive face type discs that offer high initial response with a smooth pedal feel. The type iii offers the highest overall braking confidence and control, allowing a quick qualifying time or top results in sprint races. Gt-s systems contain advanced calipers that include racing style radiators, dual inner piston seals, an inner pressure seal and an outer wiper seal. This innovative design provides the best combination of performance and long-lasting track use. The calipers are hard anodized in black (machined brembo logo in red) for resistance to corrosion and...(choose a part on the right to read more)

Features
• improved two piece 996 GT3 lower control arm design
• stronger than cast motorsport cup arms
• allows proper camber adjustment
• uses GT3 shims to adjust camber & lower control arm length (sold separately)
• high-strength steel alloy spherical bearings, completely serviceable unlike the motorsports arms
• sealed monoball inner bearing
• allows easy access to inner arm hardware
• includes adjustable thrust arm bushings to adjust caster and wheelbase
• a must have for all track and race enthusiast
• each kit includes pair of 2 arms
• fits both front and rear axles
• compatible with all 996/997/987/981 models except GT4

If you are doing sheet metal repair to your Porsche (or any car, for that matter), wurth seam sealer is a must-have. It is used to seals seams & joints that are spot welded, riveted, or bolted. permanent adhesion to bare or painted surfaces. Brush able, low odor formula goes on thick to seal completely, and provides an OEM appearance when finished. Will not sag, shrink, or crack, and is paint-ready in 45 minutes. Temperature range from -13ºf to +176ºf.

General Fitment

The brembo gran turismo s (gt-s) braking system is ideal for clubsport and sprint type track events. The GT-s type iii system utilizes brembo type iii aggressive face type discs that offer high initial response with a smooth pedal feel. The type iii offers the highest overall braking confidence and control, allowing a quick qualifying time or top results in sprint races. Gt-s systems contain advanced calipers that include racing style radiators, dual inner piston seals, an inner pressure seal and an outer wiper seal. This innovative design provides the best combination of performance and long-lasting track use. The calipers are hard anodized in black (machined brembo logo in red) for resistance to corrosion and...(choose a part on the right to read more)

Trying to save weight at the track? These makrolon polycarbonate race windows are very lightweight, strong and durable. They are made in Germany. Includes right and left rear quarter windows and the rear windshield. All with seals for a complete installation.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

Trying to save weight at the track? These makrolon polycarbonate race windows are very lightweight, strong and durable. They are made in Germany. Includes right and left rear quarter windows and the rear windshield. Does not include the seals.

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

Trying to save weight at the track? These makrolon polycarbonate race windows are very lightweight, strong and durable. Made in Germany. Weight: 2.7 kg (5.9 lbs)

This item may need to be sourced from Germany and would take 2-4 weeks to arrive. Once ordered it cannot be canceled. Please call to check stock or request expedited shipping.

As our classics age, the original gaskets and seals become brittle, crack and disintegrate. The windshield seal is essential to prevent moisture damage and rust developing on the cowl. This is a high-quality OEM replacement, designed to perform like the original. Sold individually. 1 necessary per car.